What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data? A.RPI at 50% of IO rate B.RPI at 25% of IO rate C.PI to 25% of PAC scan rate D.Set RPI to 50% of PAC scan rate Show Answer
A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and machine level I/O have been placed on VLAN 104.Both standard controllers must monitor a photocell on this machine.Which IP address is used to transfer this status information? A.10.17.104.16 B.192.168.1.16 C.126.96.36.199 D.188.8.131.52 Show Answer
Refer to the exhibit. An expansion project added an E-Tap and Device Level Ring to interface FastEthernet1/1of L2SW1. The administrator has looked at the logs of L2SW1 and found thatFastEthernet1/1 was in an error-disabled state.Using command line access on L2SW1,the administrator issued the following commands in configuration mode: L2SW1(config)# interface FastEthernet 1/1L2SW1(config-if)# shutdownL2SW1(config-if)# no shutdown […]
ProfiNET has been disabled on a Cisco Industrial Ethernet switch.Which CLI command will correctly enable ProfiNET on the switch? A.switch(config)#profinet B.switch(config-if)#switchport profinet vlan 10 C.switch(config)#vlan 10 profinet D.switch#enable profinet Show Answer
Which describes a best practice rule for controlling traffic between the corporate network and the controls network?
Which describes a best practice rule for controlling traffic between the corporate network and the controls network? A.Outbound traffic from the control network to the corporate network and outbound traffic from the corporate network to the control network can be restricted based on source and destination address only. B.Outbound traffic from the corporate network to […]
Profinet has been disabled on a Cisco Industrial Ethernet switch, which CLI commands correctly enable ProfiNET on VLAN 10? A.switch(config)#profinet switch(config)#profinet vlan 10 B.switch#enable profinet switch(config)#profinet vlan 10 C.switch(config)#profinet switch(config)#vlan 10 switch(config-vlan)#profinet D.switch#enable profinet switch(config)#vlan 10 switch(config-vlan)#profinet Show Answer
You are called at home at 3am by an unskilled machine operator with a suspected networkrelated problem; the controller LEDs are all normal but the output module’scommunications LED is not on. The operator has verfied the cable is functional andcorrectly connected from the communication module to the switch.What is the next check that you ask […]
Which CLI command will increase the number of available IPv4 IGMP groups and multicast routes from 256 to 1000 on this switch?
You have reached the limit of IPv4 IGMP groups available on a Cisco IE 3000 switch thatwas deployed using the Express Setup.Which CLI command will increase the number of available IPv4 IGMP groups and multicast routes from 256 to 1000 on this switch? A.switch(config)#sdm prefer routing B.switch(config)#sdm prefer vlan igmp C.switch(config)#sdm prefer routing igmp D.switch(config)#sdm […]
You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on? A.Lattency and Jitter B.Redundancy and high availability C.Explicit and Implicit messaging D.This cycle time is not possible on an Ethernet […]
Which statement is correct regarding ProfiNET communication classes? A.ProfiNET-RT traffic is carried in UDP and TCP packets B.ProfiNET-NRT is used to carry time critical status information C.ProfiNET-IRT requires switches with hardware time scheduling capabilities D.ProfiNET-NRT is prioritized as Layer-2 Class-of-Service 1 (CoS 1) Show Answer